Coke Oven Machinery
Coke oven machinery includes coal charging car, coke guide car, pusher car, quenching car and locomotive. These equipment complete coal charging and coke discharging operations for coke ovens. Apart from core tasks, they also perform a wide range of auxiliary work as follows:
Opening and closing of charging hole lids and oven doors, as well as levelling hole lids.
Coal levelling operation during coal charging into carbonization chambers.
Recovery and treatment of surplus coal generated in levelling.
Cleaning of oven doors, door frames and ascension pipes.
Cleaning of the oven top, operating platforms on machine side and coke side.
High-end vehicles are equipped with environmental protection facilities for flue gas dedusting.
Various mechanisms are installed to realize above operations. All these vehicles travel along rails alongside the battery. With the adoption of such vehicles, coke oven operations are basically fully mechanized.
The complete set of coke oven machinery operates following the 5-2 pushing sequence, controlled by unit program with manual control mode available. Interlock safety devices are installed between the pusher car and locomotive. Carrier communication telephones are equipped in each driver's cabin to improve equipment safety and reliability.
Coal Charging Car
This is a dedusting coal charging car. It adopts one-point positioning, mechanical opening/closing of charging hole lids and mechanical cleaning of ascension pipes. It is designed with screw feeding and sequential coal charging, together with an oven-top cleaning unit. Operators can control opening/closing of coal tower hoppers and coal tower vibration from the driver's cabin for convenient and reliable operation. The sealed and heat-insulated driver's cabin is fitted with air conditioning to optimize working conditions.
To achieve smokeless coal charging, the coal charging car is equipped with sleeves for docking with coke-side dust collecting main pipes and coal feeding guide sleeves.
Coke Guide Car
Functions
The right-hand type coke guide car travels on rails on the coke-side operating platform of coke ovens. Its main functions include removing and installing coke-side oven doors, guiding hot coke into the quenching car during coke pushing. Flue gas produced in coke pushing is captured by the dust collecting hood and delivered to the dust collecting main pipe via interface valves to reduce atmospheric pollution. It also carries out cleaning of oven doors, door frames and oven platforms to lower labor intensity.
All operations are controlled inside the driver's cabin. Each unit supports both unit program control and manual operation.
General Structure
The coke guide car features a steel frame with rationally arranged mechanisms, together with auxiliary facilities including ladders, railings and platforms to form an integrated unit.
It consists of steel structure, travelling device, coke guiding device, door extracting device, oven door cleaning device, door frame cleaning device, oven platform cleaning device, head and tail coke treatment device, dust collecting system, lubrication system, pneumatic piping, hydraulic piping, hydraulic unit, electrical system and air conditioning unit.
Pusher Car
Composition and Functions
The pusher car runs on rails on the machine side of coke ovens and performs a series of process operations according to specified sequences. Core functions: removing and installing machine-side oven doors, pushing hot coke out of carbonization chambers, cleaning oven doors, small oven doors and door frames, head and tail coke treatment, opening and closing of small carbonization chamber doors during coke pushing, coal levelling and surplus coal disposal.
All operations are conducted inside the driver's cabin. Travelling is manually controlled, while other actions can be operated automatically or manually via buttons.
General Layout
The travelling device is arranged on the travelling platform. The first floor platform accommodates the pushing unit, door extracting unit, door cleaning unit, frame cleaning unit, head & tail coke treatment unit, oven platform cleaning unit and hydraulic system. The second floor platform is equipped with coal levelling unit, small door cleaning unit, driver's cabin, electrical room, air conditioning and air purification system.
Structure and Working Principle
The equipment adopts a five-oven-space one-time positioning structure. The pushing unit serves as the center. The coal levelling and door frame cleaning devices are arranged on the left, and the door extracting, door cleaning and small door cleaning devices are arranged on the right. Operations follow the 5-2 pushing sequence. While pushing coke, the machine can conduct coal levelling for the previous oven and small door cleaning for the next oven simultaneously. The door extracting device and door frame cleaning device are installed on both sides of the pushing unit. One-time positioning is realized through rotary S-track movement.
Quenching Car and Locomotive
Quenching Car
Structure
The quenching car comprises frame, bogies, left and right end walls, front and rear side walls, discharge doors, bottom plate, guardrail, door opening mechanism and braking system. Heat-resistant cast iron plates are fitted on end walls, side walls, bottom plate and discharge doors. Cast steel inclined supports connect the bottom plate and front side wall to enhance carriage rigidity and reduce thermal deformation of the front side wall. The bottom plate is inclined at 28° to facilitate smooth coke discharge.
Working Principle
The door opening mechanism adopts gear and rack transmission. The rack is pinned to the piston rod of the driving cylinder. Bidirectional air supply to the cylinder drives the rack to move back and forth. The gear meshed with the rack rotates the main shaft, and swing rods mounted on both ends of the shaft push the levers to open or close the discharge doors for coke unloading.
Swing rods of the door opening mechanism can rotate 128° along the circumference. Rigid limit blocks and limit switches are installed at two extreme positions of the 128° swing range, ensuring the opening width of each discharge door stays within 650±20 mm. Limit switches only send signal prompts when doors reach extreme positions.
The quenching car is towed by the locomotive. Air supply for the door opening cylinder comes from the locomotive. Compressed air is delivered via hose connectors and pipelines to the cylinder. The locomotive can couple with either end of the quenching car, and air pipelines can be connected on both ends. When coupled on the left end, close the ball valve on the right pipeline of the quenching car; when coupled on the right end, close the ball valve on the left pipeline.
The braking system adopts air shoe brakes. Compressed air from the locomotive acts on brake cylinders and tie rods to press brake shoes against wheels for braking.
Locomotive
Structure and Working Principle
The locomotive mainly consists of upper car body, lower travelling device, braking system, pneumatic system, air conditioning system and electrical system.
Operators can walk directly to the coke-side oven platform via high walkways on the locomotive. The driver's cabin is mounted on the side outside the car body for good sightlines. Air compressor and electrical cabinets are placed inside the machine room, and the air cooler compressor is installed outside the driver's cabin. Two air receivers and power sliding line supports are arranged on the oven-facing side.
The car body is assembled by machine room, driver's cabin, platforms, staircases and railings. Components are connected by bolts and welded after on-site installation.
The machine room is a steel structure with an access hole on the top for maintenance and a side door beside the staircase for easy access. The top is covered with checkered plates and serves as a service platform.
Supported by platforms, the driver's cabin is installed outside the car frame. Thermal insulation materials are adopted for the roof and side walls, and interior surfaces are decorated with color coated plates. The cabin is equipped with operation console, signal communication devices and an air conditioner.
The travelling device mainly includes transmission mechanism, frame, coupler, disc springs and braking units.
Two sets of transmission mechanisms separately drive one wheelset each. Each set consists of an electric motor connected to a horizontal reducer via universal shaft. The split final gear of the reducer is rigidly connected to the wheel axle. The connection between transmission mechanism and frame is semi-rigid and semi-elastic. Air shoe brakes are additionally equipped to support low-speed operation during coke receiving. The frame is welded from low-alloy steel with high strength and rigidity. Wheelsets are flexibly supported on the frame by combined disc springs. The bearing boxes are guide frame type and fitted inside frame guides. The frame rests on bearing boxes via disc springs. For optimized braking performance, combined braking of pneumatic shoe brakes and disc brakes is applied, and brake shoes are made of high-phosphorus cast iron.
The pneumatic system supplies compressed air for locomotive braking, opening/closing of quenching car discharge doors and quenching car braking. Two air compressors are configured (one running, one standby). Compressed air is stored in air receivers and supplied to actuators through control components. Solenoid valves control door movement and locomotive braking.
The pneumatic system is equipped with two air receivers with a total storage capacity of 3.4 m³ and working pressure ranging from 0.45 MPa to 0.7 MPa. After one inflation, sufficient air can support multiple operation cycles. Even if the air compressor breaks down, residual compressed air can finish coke unloading from the quenching car.

